Corresponding author: Olga I. Bulakh (o.i.kataeva@gmail.com)
Academic editor: Yury Kazansky
High-temperature gas-cooled reactor (
The range of output coolant temperatures in high-temperature reactors within the limits of 750–950 °C predetermines the use of graphite as the structural material of the reactor core and helium as the inert coolant. Application of graphite ensures higher heat capacity of the reactor core and its practical non-meltability.
Residence time of reactor graphite depends on the critical value of fluence of damaging neutrons (neutrons with energies above 180 keV). In its turn, the value of critical neutron fluence is determined by the irradiation temperature and flux density of accompanying gamma-radiation. The values of critical fluence for graphite decrease within high-temperature region of 800–1000 °C to 1·1022 – 2·1021 cm–2, respectively. The compactness of the core results in the increase of the fracture of damaging neutrons in the total flux. These circumstances predetermine relatively low values of lifespan of graphite structures in high-temperature reactors.
Design features and operational parameters of
The map and methodology for re-shuffling fuel blocks of the
Development and implementation of new generation of nuclear reactors recognized in pursuance with IAEA classification as the safest reactor types are the promising direction of development of nuclear industry. One of such types of advanced nuclear reactors are the high-temperature gas-cooled reactors (
Research conducted in the field of investigation of functionality of reactor-grade graphite in Russia is directed towards finding the solution of the main problem of objective interpretation of already existing experience of graphite operation in commercial and power uranium-graphite reactors for the purpose of application of graphite in the design of advanced nuclear reactors of
Highly efficient energy generation (thermal efficiency of about 50%);
Use of high-temperature heat for different production purposes;
Self-protection properties of reactor core, as well as the impossibility of core meltdown in case of accident;
Possibility of implementation of different options of reactor fuel cycle (uranium-plutonium, thorium-uranium);
Reduced radiation and thermal impact on the environment;
Forecasted acceptability of financial performance indicators as pertains to the cost of generation of electricity as compared with alternative energy sources.
Implementation of
Cross-section of the reactor core is the hexagonal collar consisting of 1020 hexagonal prismatic fuel blocks arranged in 102 columns of 10 fuel blocks each. Fuel blocks are shaped in the form of hexagonal graphite prism with elements containing nuclear fuel inserted in the channels bored through the block (
а). Fuel block of
Uranium dioxide with U235 enrichment reaching 19.9% distributed in the graphite matrix in the form of separate fuel microelements with four layers of coating made of pyrolytic carbon and silicon carbide is used as the fuel in the reactor core.
Cross-section of fuel microelement is shown in Fig.
Each fuel block incorporates 198 fuel channels containing press-fitted fuel microelements. Uranium load per one fuel block amounts to 4.25 kg. Density of graphite in the matrix of fuel elements and fuel blocks is equal to 1.7 g/cm3.
Main characteristics of collar-shaped reactor core are represented in Table
Main characteristics of
|
|
Thermal power of the reactor core, MW | 600 |
Internal equivalent diameter, m | 2.96 |
External equivalent diameter, m | 4.84 |
Core height, m | 7.92 |
Average specific power yield, MW/m3 | 6.6 |
Number of fuel columns in the reactor core | 102 |
Number of fuel blocks in the column | 10 |
Uranium load per one fuel block, kg | 4.25 |
U235 enrichment, % | Up to 19.9 (14 – average for the core) |
Burnable neutron absorber (natural boron) load per each of the six rods in the fuel block, g | 1.13÷2.25 |
Interval between core reloading and re-shuffling, eff.days | 540 |
Fuel residence in the core, eff. days | 1080 |
Maximum fuel burnup, MW·days/ tU | 1.4·105 |
Maximum reactivity margin in cold non-poisoned state in the process of fuel residence campaign, % δk/k | 12.5 |
Temperature reactivity effect, % δk/k | < 4.9 |
Maximum specific power density of the core, W/m3 | < 23 |
Efficiency of 48 pairs of control rods on 5 m run, % δk/k | > 14 |
Reactor core poisoning with Xe, % δk/k | > 2.6 |
Efficiency of 18 channels of spherical reactivity compensation system, % δk/k | > 8.2 |
Coolant pressure, MPa | 7.07 |
Temperature, core inlet / outlet, °C | 490 / 850 |
Maximum permissible fuel temperature in normal operational conditions (w/o accounting for fuel overheating factors), °C | 1250 |
Maximum permissible fuel temperature during accidents, °C | < 1600 |
Number of reactivity compensation rods | 54 |
Number of channels of redundant reactivity compensation system | 18 |
Determination of neutron flux spectrum in the reactor core was performed by solving the set of multi-group neutron diffusion equations by iterative method. The iterative method was implemented within the framework of multi-group calculation using the methodology described in (
All group values and, consequently, the values averaged over the spectrum to be entered in the expression for determination of effective neutron multiplication factor
Maximum reactivity margin in cold, non-poisoned conditions amounts in this case to ρ = 12.6% in the course of fuel residence in the reactor core. The obtained value of reactivity margin practically coincides with the design value (ρ = 12.5%) which demonstrates satisfactory quality of the calculation.
Evolution of nuclide composition of nuclear fuel in the process of its irradiation can result in significant variation of values of fluxes of damaging and thermal neutrons, which will affect the expected service life graphite. Variation of concentrations of the following nuclides: U235, U238, Pu239, Pu240, Pu241, Pu242, products of fission of U235 and Pu239 is taken into account in the present study (
Dependences of fluxes of thermal and damaging neutrons on nuclear fuel burnup are presented in Fig.
Dependences of fluxes of thermal Фt and damaging Фd neutrons on the nuclear fuel burnup
Bred fissionable plutonium nuclides possess high neutron absorption and fission cross-sections in thermal energy region and, besides that, average number of secondary fast neutrons per one fission event is higher than that for U235. This leads to the increased hardness of neutron flux spectrum in the course of irradiation of nuclear fuel, as the result of which damaging neutron flux density by the end of fuel residence in the core is practically by four times higher than that for fresh fuel.
In order to estimate service life of graphite it is necessary to determine the distribution of graphite irradiation temperature over the reactor core, because it is the decisive factor influencing the value of critical fluence of damaging neutrons. Non-uniformities of temperature distribution and the accumulated fluence of damaging neutrons over the reactor core result in the significant changes of local volumes of graphite and serve as one of the main causes of deformation and destruction of fuel.
Axial distribution of power release within fuel column was preset in accordance with (
Minimum value of heat release in the fuel along the core height amounted to 44%, which corresponds to the numerical value equal to 4.17 МВт/м3. Maximum value of heat release amounted to 9.49 MW/m3.
Elementary cell with radius equal to
Elementary cell of reactor core with radius
The elementary cell and heat release profile allow determining the field of graphite irradiation temperatures by applying the standard methodology of thermal physics calculations (
The value of “expired lifespan” is used in (
EL =
where
If EL ≤ 1, than it is recognized that the operational characteristics of graphite are still preserved. Irreversible changes of the operational characteristics, first of all deformation and, following this, crack formation accompanied by degradation of thermal physics properties can be expected for EL >1.
Duration of nuclear fuel residence in the core amounts to 1090 eff. days (two years of 545 eff. days each), on the basis of which calculation of the graphite expired lifespan was performed. Variation of power release over the core radius was not taken into account. Dependence of the expired lifespan of graphite over the core height is shown in Fig.
Time dependence of the expired lifespan of graphite along the core height: 1 – nuclear fuel residence time equal to 1090 eff. days; 2 – time between fuel re-shuffling in the core equal to 545 eff. days
Calculated value of the expired lifespan exceeds unity by the end of nuclear fuel residence time in the core, which demonstrates the possibility of destruction of fuel block inside the reactor core. Maximum value of graphite lifespan already expired by the moment of fuel re-loading amounted to 71%, and the minimum value was equal to 8%. Therefore, fuel block must be necessarily moved at the moment of fuel re-shuffling and re-loading from dangerous sections to safe ones taking account the value of radial-azimuth heat-release non-uniformity factor. The data from (
Map of
Two cycles of nuclear fuel burnup are assumed in the reactor (
Values of energy release are repeated for different sections of the core, based on which they are grouped, therefore, by the number of fuel blocks with similar values of non-uniformity factors and the year of irradiation. Values of expired graphite lifespan at the end of each nuclear fuel irradiation micro-campaign are of the utmost interest, since the sequence of re-shuffling of fuel blocks ensuring graphite serviceability and allowing achieving the design fuel burnup can be developed by analyzing these values.
Dependences of nuclear fuel burnup depth and expired lifespan of fuel blocks at the end of fuel irradiation micro-campaign along the height of fuel column with maximum (
а). Dependence of burnup depth along the core height for fuel block at the end of nuclear fuel irradiation micro-campaign: 1 – maximum
It is evident from the figure that radial non-uniformity over the reactor core significantly affects not only the fuel burnup, but, as well, the lifespan of fuel blocks. Irradiation of fuel blocks in the central part of the core results in the achievement of maximum fuel burnup, while the fuel in the upper and lower parts does not reach the intended burnup.
Examining the effects of arrangement of fuel blocks in the reactor core it is clear that with increase of temperature and radial non-uniformity of energy release the expired fraction of graphite lifespan increases and reaches the value of about 0.8 near the lower elevation mark of the core for maximum value of the heat-release non-uniformity factor. Continuation of use of graphite on these sections will lead to irreversible changes of operational characteristics, reduction of thermal conductivity and deformation of the blocks, since their expired lifespan will exceed the critical value already during the third year of irradiation of the fuel block.
Thus, the methodology of fuel blocks re-shuffling presented below (Fig.
Diagram of re-shuffling graphite blocks
Methodology of re-shuffling fuel blocks.
Reactor core is divided into two part along the height.
Fuel blocks from the periphery of the first (upper) part of the core from fuel columns irradiated in the conditions with high values of radial non-uniformity swap places with fuel blocks extracted from the heat release plateau area of the second (lower) part of the core and go to fuel columns irradiated in the conditions with low values of radial heat release non-uniformity.
Fuel blocks from the heat release plateau of the first (upper) part of the core from fuel columns irradiated in the conditions of high radial non-uniformity swap places with fuel blocks from the periphery of the second (lower) part of the core and go to fuel columns irradiated in the conditions of low radial heat release non-uniformity.
Fuel blocks from the periphery of the first (upper) part of the core from fuel columns irradiated in the conditions with low radial non-uniformity coefficients swap places with fuel blocks in the area of heat release plateau of the second (lower) part of the core and go to fuel columns irradiated with high radial heat release non-uniformity coefficients.
Fuel blocks from the area of heat release plateau of the first (upper) part of the core from fuel columns irradiated in the conditions of low radial heat release non-uniformity coefficients swap places with fuel blocks on the periphery of the second (lower) part of the core and go to fuel columns irradiated with high radial heat release non-uniformity coefficients.
Area of the plateau occupies the central part of the core along its height where the value of heat release is the closest to the maximum value.
The above combination is exercised for the whole reactor core, which allows levelling the heat release field, ensuring the design burnup depth, as well as extending service life of graphite in the
а). Dependence of burnup depth on the height of the reactor core at the end of nuclear fuel irradiation campaign: 1 – without taking re-shuffling of graphite blocks into account; 2 – taking re-shuffling of graphite blocks into account. b). Dependence of the value of expired lifespan of graphite along the core height at the end of reactor fuel irradiation campaign with different non-uniformity of heat release after re-shuffling the blocks at the middle of fuel irradiation campaign
Discrepancy between the maxima in the dependences of nuclear fuel burnup depths and expired lifespan of graphite of fuel blocks along the core height of
Part of fuel block may be destroyed before the design value of nuclear fuel burnup depth is reached;
Excess of the design value of nuclear fuel burnup depth occurs with serviceability of nuclear fuel retained;
Neither the design value of nuclear fuel burnup depth nor the limiting value of expired lifespan of graphite are reached.
Layout and methodology of re-shuffling and re-loading fuel blocks of
* Russian text published: Izvestiya vuzov. Yadernaya Energetika (ISSN 0204-3327), 2019, n. 3, pp. 40–52.